Elegant Patio Chair Makeovers

I am so excited for our new patio space and have already enjoyed time out here eating lunch, reading, or catching up on some work. I started looking for some lounge chairs, but I couldn’t quite find what I wanted – or more accurately, what I wanted was way too $$$. But this story has an happy ending! I found these used chairs and made them over for $ to complete our patio space!

It’s no secret that I love anything with the look of cane or faux bamboo and also that I have a weakness for Craigslist finds! I spotted this set on Craigslist for $50, and when I showed up, the woman said I could have it for free. She also let me take the chairs without the table, so my karma of giving things away when we moved last year came back to me! I also picked up the chairs near my old neighborhood hardware store, so I stopped by to get some supplies and painting tips.

Here’s how to do it:

  • I started by cleaning off as much rust as possible. I used an old screwdriver, sandpaper, and steel wool
  • I prepped the chairs with deglosser and metal primer
  • I then finished them off with white gloss spray paint
  • The cushions were in decent condition, just faded, so I found these new slipcovers to freshen them up!

Here are some more pictures of our “new” chairs.

I feel they came pretty close to my inspiration pics, and all with the satisfaction with saving some money and a good DIY!

Everyone loves a good before and after pic:

I look forward to many more hours enjoyed out here with friends, family, or curled up with a good book!

Julie AKA “Jewels”

New Powder Room – Chair Rail and Baseboard

Oh my, it’s May! And it’s a very good thing that my friend Ari advised me to start my bathroom makeover after my son’s birthday party. That was two months ago, and I had some delusion that I could get the whole project done in a week – on top of taking care of the kids, going to work, and planning the party itself. I hadn’t wanted people to see the ugly old powder room at the party, but waiting turned out to the right decision.

As they say, good things come to those who finally get their behinds in gear and do some work. I had a little spurt of energy in April, when I put up the wallpaper. Now, I’ve finally added the new trim. I put up a chair rail and used the trick of adding a thin piece of molding a few inches above the existing baseboard to give the illusion of a more substantial baseboard. Adding new trim gives your room architectural detail and makes it feel more elegant and finished.

So here’s what I did:

1) Choose trim

For both the chair rail and the baseboard extension, there aren’t standard shapes, so pick something that you like. I picked a heavier piece with a slope for my chair rail and a very thin piece for extending the baseboard. I get almost all my home improvement supplies at our local hardware store, Papenhausen. I love that I can walk there, and the staff is always friendly and knowledgeable. In a relatively small space, they have just about anything you could need. This time, however, I did end up at a big box store to get a wider selection. It’s almost endless!


Left: small trim piece used to extend the baseboard. I think this is called “stop” molding.
Right: heavier trim piece used for a chair rail. This piece was pre-primed.

2) Measure (twice), cut (once – I wish!)

Measure each wall. If you have an old house like ours, measure at the exact height you will mount each piece, since the walls may not be even. Chair rail is usually mounted 36″ +/- 2″ from the floor. I picked the height of the baseboard to avoid some plumbing. A lot of older and more expensive homes have high baseboards, so this is a great trick to mimic that look, without using a lot of trim, since you’ll just be painting the wall between the old baseboard and the new trim all one color, so it looks like a single tall piece of molding.

You will need a way to make miter cuts (cuts on a 45 degree angle). If you have a table saw, follow the instructions for using that. If not, you can use a tool called a miter box along with a handsaw. Cut the trim into the lengths you need, with mitered ends at each corner.

DO NOT miter the ends that will meet that meet the door jamb, as these should be flush. Yes, I made this mistake – I must have been to0 excited about figuring out how to use the table saw.


Cut the trim pieces at 45 degree angles at the corners.

3) Install the trim
Mark a level line and nail the trim in place with panel nails. You can hammer the nails partway into the boards before nailing them into the wall. That makes it feel less like you need three hands! Once the boards are installed, countersink the nails, i.e. use a nail set or another nail to push the head of your nail into the board, so it doesn’t stick out.


Tools for installing trim:
1) level
2) hammer
3) panel nails
4) nail set (you can also use a large heavy nail)


Hammer the nails partway into the molding pieces before installing.

4) Patch and caulk

Luckily, this step can hide a multitude of errors, and there were a few! Use wood filler to cover the nail holes and any larger gaps (gaps? What gaps?). Sand the patched areas smooth. Then use paintable caulk to run a line along the top of the molding to fill the small space between the wood and the wall.

tools for patching molding

Tools for patching and caulking:
1) sandpaper. I store mine in a magazine file.
2) caulk and caulk gun. You can get ones that you squeeze by hand, too, so the gun is not necessary. Any kind that is paintable is fine.
3) putty knife for smoothing filler
4) wood filler


Wood filler used to cover the nail holes and fill the gap at the corner.


The caulk fills the gap between the new trim and the wall.

5) Ready to paint!

All the trim is installed. The next step is to prime and paint this area. I’m going to use a medium grey on the wall below the chair rail, similar to the inspiration room by Sarah Richardson.

powder room trim

The new chair rail and baseboard extension are in place and ready for priming and painting!

An inspiration for our powder room. Click the image to go to the image on Sarah Richardson’s website.

By the way, I learned how to install trim watching the Christopher Lowell over a decade ago. Did any of you watch him? He did a great job breaking projects down into steps, and he ended every show by enthusiastically saying, “You can do it!”. Those words kept running through my head as I was working!

Yay! The finish line is in sight for this bathroom makeover. I’m ready to paint, and I’ll call in a plumber to replace the sink with a new vanity. I hope I can post the completed powder room soon. Until then, remember, you can do it!

UPDATE: The powder room is finished! You can see it here.